	pumps and pumping systems

Information
- HVP
- ZBO

Hydrophore tanks HVP

Application

The HVP pressure tank is made of fully welded low-carbon steel sheets and available with the following capacities: 100, 200, 300, 500, or 1000 litres. Water supply automation with hydraulic accumulator tanks can only be connected to depressurised water intakes. The tank shall only be installed in the systems with the maximum pressure below the design pressure of the tank type. The outer and inner surfaces are protected with galvanic coating.

The tank is vertically oriented with three feet welded at the circumference. The cylindrical section features a water gauge tube installed between elbows to display the water level. The cleanout opening is installed in the shell. The top section of the tank features a G2 hole closed with a threaded plug which houses a pressure gauge.

The pressure tanks are intended for:

supply water to residential and utility buildings from:
- on-site water intake;
- shallow aquifers accessed by cased wells;
- drilled wells;
- ponds;
- reservoirs;
hydraulic accumulator sets to act as the air/water tank;
allotment gardens;
summer cottages;
water supply of fountains.

Design and technical parameters - HVP100, 200, 300, 500 tanks

Lp.	Drawing	Cap. m³	Dz mm	H mm	h mm	H1 mm	H2 mm	H3 mm	H4 mm	Gp mm	Gd mm	Design pressure MPa	Initial pressure MPa	Design temp. [°C]	Weight [kg]
1.	HVP100	0,1	500	767	400	545	270	360	360	2,5	3,0	0,9	1,29	20	40
2.	HVP200	0,2	550	1066	712	780	320	360	360	2,5	3,0	0,9	1,29	20	50
3.	HVP300	0,3	550	1354	1000	920	320	360	360	2,5	3,0	0,9	1,29	20	60
4.	HVP500	0,5	750	1387	1000	970	370	425	425	2,5	3,0	0,6	0,86	20	115

Design and technical parameters - HVP151, 201, 301 tanks

Lp.	Drawing	Cap. m³	Dz mm	H mm	h mm	H1 mm	H2 mm	H3 mm	H4 mm	Gp mm	Gd mm	Design pressure MPa	Initial pressure MPa	Design temp. [°C]	Weight [kg]
1.	HVP151	0,15	500	967	600	570	270	360	270	2,2	2,5	0,6	0,86	20	45
2.	HVP201	0,2	550	1066	712	780	370	360	270	2,2	2,5	0,6	0,86	20	48
3.	HVP301	0,3	550	1354	1000	920	320	360	270	2,2	2,5	0,6	0,86	20	57

Design and technical parameters - HVP1001 tanks

Lp.	Drawing	Cap. m³	Dz mm	H mm	h1 mm	h2 mm	h3 mm	h4 mm	Gp mm	Gd mm	Design pressure MPa	Initial pressure MPa	Design temp. [°C]	Weight [kg]
1.	HVP1001	1,0	908	1952	1200	578	600	638	4	4	0,8	1,14	20	208

Design and technical parameters - HVP1500 tanks

Lp.	Drawing	Cap. m³	Dz mm	H mm	h1 mm	h2 mm	h3 mm	Gp mm	Gd mm	Design pressure MPa	Initial pressure MPa	Design temp. [°C]	Weight [kg]
1.	HVP1500	1,5	1010	2332	1500	800	700	5	5	10	14,3	20	340

by Application